| Before you start: 1. Read the instructions carefully. 2. Work over a sink or a surface covered in layers of newspaper (just in case). 3. Only re-fill a cartridge that has just run out ~ this kit will not work with old dried out cartridges. Even 30 min- utes can ruin a cartridge if it dries out! 4. Have your printer manual handy for instructions on inserting a “new”cartridge. 12A1970, 12A1975, 17G0050, 13400HC, 1361400, 1380620, 1382060, 16G0055 ~ Same refill instructions apply to all. Same instructions for BT MultiJet 3000 These cartridges also fit a variety of Compaq, Samsung, Brother, OKI & Kodak printers ~ check with your supplier for compatibility. 1. Enlarge the vent hole on the top of the cartridge using the screw provided. (Important: Do not remove the top). 2. Insert the black ink syringe needle into the vent hole and push down into the centre of the cartridge. Slowly inject up to 25ml. of black ink into the cartridge. 3. Insert the cartridge back into the printer as per the printer instruction manual.
IMPORTANT - for best results, cartridge should be refilled whilst some ink remains. Empty cartridges should be refilled immediately. This work is best done over the sink.
12A1980/ 12A1985/ 17G0060/ 13619HC/ 1380619/ 16G0065 ~ same refill instructions apply to all. Same instructions for BT MultiJet 3000. These cartridges also fit a variety of Compaq, Samsung, Brother, OKI & Kodak printers ~ check with your supplier for compatibility. 1. The filler holes of the cartridge are located under the top. Remove the top before refilling by carefully prying it off with a thin metal blade such as a penknife. Be careful not to damage the sensors on the back of the cartridge. 2. Cover the other two holes with tape while filling one. This will prevent cross contamination. 3. Insert the correct (cyan, yellow or magenta) filling needle into the filler hole of the colour to be refilled. You may feel a slight pressure because the cartridge contains a sponge. 4. Slowly inject up to 8ml. of ink until the ink begins to surface on top of the sponge. 5. After refilling the top can be put back on with adhesive tape. 6. Insert the cartridge back into the printer carefully following the instructions in the printer manual.
IMPORTANT - When you take off the colour cartridge cap you will notice that the sponge is white. Do not change the sponge colour. Fill the individual colours until the colour just begins to show in the white sponge. IMPORTANT - For best results, cartridge should be refilled whilst some ink remains. Empty cartridges should be refilled immediately. This work is best done over the sink. Olivetti ArtJet10, ArtJet20, JP150, JP150W, JP150WS, JP170, JP170C, JP170S, JP190, JP192, JP250, JP270, JP350, JP350S, JP350WS, JP360, JP370, JP450, JP470, JP50, JP70, JP790, JP792, JP795, JP883, JW900, JW910, Linkfax series ~ Black only OFX series ~ BLACK ONLY. BT MultiJet ~ all models. ADLER Royal FX620i, Royal FX620Ti, Royal FX630, Royal FX631, Royal FX635, Royal FX636, Royal FX650, Royal FX655, Royal JPR 7825WS, Royal JPR 7830, Royal JPR 7845, Royal JPR 7847/c, Royal JPR 7860. Brother LW700ic, LW750ic, LW800ic, LW810ic, LW830ic, LW840ic. Citizen 300121, CIJ660, CIJ660C, Printva 600C, Projet I, Projet II, Projet IIC.
10N0016, 10N0217, 18C0032 18L0032 BLACK BLACK
1. Enlarge the vent hole on the top of the cartridge using the thumbscrew provided. Do not remove the top. 2. Insert the black syringe into the vent hole and push down into the centre of the cartridge. Slowly inject about a third to one half of a full syringe worth of black ink into the cartridge. 3. Set above a paper towel for half an hour as a drip precaution. Expect a few drips. Do not allow the cartridge to touch the paper towel at this point, since the towel will draw out the ink. 4. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions. 5. If necessary leave cartridge in printer for up to 24 hours. (Allows ink to flow to the print head). IMPORTANT - For best results, cartridge should be refilled whilst some ink remains. Empty cartridges should be refilled immediately. This work is best done over the sink.
1. The filler holes of the cartridge are located under the top. You must remove the top before refilling by carefully prying it off CAREFULLY with a knife such as a pen knife. 2. Insert the filling syringe of the appropriate colour into the filler hole of the colour to be refilled. 3. SLOWLY inject up to 3ml. of ink (there is 30 ml in each syringe) until the sponge is saturated.
VERY IMPORTANT: When you take off the colour cartridge cap you will notice that the sponge is white. Fill the individual colours until the colour JUST begins to show in the white sponge. 4. After refilling the top can be put back on with adhesive tape. 5. Replace the cartridge and run 2 - 3 cleaning cycles as per printer instructions. IMPORTANT - For best results, cartridge should be refilled whilst some ink remains. Empty cartridges should be refilled immediately. This work is best done over the sink. |